Cable Gland Testing

Are You Looking for Cable tray Safe Working Load Test (SWL)?

Posted on Updated on

Cable tray Safe Working Load Test (SWL)

Cable tray/ Protective castings must be designed to the below said ambient temperatures

  • -25 ºC to 90 ºC for outdoor use
  • +5 ºC to 90 ºC for indoor use.

Safe working load is one of the mechanical requirements assigned to meet by the cable tray/ protective castings. Another mechanical requirement is the Impact resistance Test. But in this article we are focusing on Safe Working Load. Testing must be performed at the above declared temperatures.

 The criteria that a cable tray must satisfy are:

  1. The maximum deflection should not exceed L/100 where L is the distance between the supports.
  2. No mechanical defects or failure are observed when tested at 1.7 * SWL.

How to place the Loads :

All the loads must be uniformly distributed (UDL) over the length and width of the sample. The loads have to be applied in a way that uniform distribution is ensured even in case of extreme deformation of the sample.  For settlement of the samples, a pre load of 10 % of the test load unless otherwise specified, should be calibrated to zero.

The gradually increase the load longitudinally and transversely up to the test load continuously or in increments. These increments should not exceed about a quarter of the SWL.

After loading, the deflection should be taken at the points specified to give a practical mid-span deflection.

The samples should be left and the deflection measured every 5 min until the difference between two consecutive set of readings is less than 2 % with regard to the first set of 2 consecutive readings. The first set of readings calculated at this point is the set of deflection measured at the test load.

After this treatment, the test load samples, their joints and internal fixing devices, should show no damage or cracks visible to normal view or corrected vision without magnification.

After this, load is increased to 1.7 times the test load.

The samples should be left and the deflections measured every 5 min until the difference between two consecutive sets of readings is less than 2 % with regard to the first set of the two consecutive sets of readings. The samples should sustain the increased loading without collapsing. Buckling and deformation of the samples is permissible at this loading.

Note:

Tests should be carried out for the smallest and largest sizes of cable

Trays lengths or cable ladder lengths, having the same material, joint and

Topological shape.

If Your Buyers Demanding for Cable tray Safe Working Load Testing – Contact Now!

Kindly send us the following Details, So that we can provide you quotation for the same:

  1. Product Name, Technical Specifications and Brochure
  2. Product Images
  3. Total Number of samples Required: 2

Wish this blog post will be help. If you have any other questions, please feel free to contact us. ITCIndia team looking forward work with you and get better together!

Mr. Puneet Sharma | Call: 08196980555 | E-mail: ITCIndiaOne@Gmail.Com

Get Instant Quotations, Fill the Enquiry form:

Cable gland Testing Laboratory, Cable Glands Test as per BS 6121, Cable gland Testing IEC- EN 62444- 2010

Posted on

Tests on Cable Glands as per BS 6121 / IEC- EN 62444- 2010

Cable gland Testing Laboratory, Cable Glands Test as per BS 6121, Cable gland Testing IEC- EN 62444- 2010

Searches related to Cable gland Testing laboratory in india, Cable gland Testing Services, Cable gland Test lab, Cable Glands as per BS 6121 / IEC- EN 62444- 2010, Cable Glands Test as per BS 6121, Cable gland Testing bs en 50262, Cable gland Testing bs 6121 standard, en 50262 cable gland Testing, cable gland Testing iec 62444, cable gland Testing bs 6121, CABLE GLAND Testing STANDARDS

ITC India NABL Accredited Electrical Safety Testing Laboratory Service Provider of Cable Glands Testing as per BS 6121 / IEC- EN 62444- 2010, If you are looking for Cable Glands Testing Laboratory in Mumbai, Pune, Maharashtra, Ahmedabad, Gujarat, Bangalore, Karnataka, New Delhi, Baddi,Chennai, Tamil Nadu, Panchkula, Haryana, Ambala, Chandigarh, Ludhiana, Mohali, Punjab, kolkata west Bengal, India you can feel free to contact us.

Cable Gland Testing list Performed by ITCIndia:

  • Cable Retention Testing
  • Cable Anchorage Pull Testing
  • Cable Anchorage Twist Testing
  • Impact Testing
  • Torque Testing
  • Ingress Protection Testing
  • Electrical Continuity Testing
  • Insulation Resistance Testing

                                                                         

Cable Glands Testing Plan as per 62444

Sr.No Clause Test Title
1. 7.1 Marking
2. 8 Construction
3 9 Mechanical properties
4. 9.2 Cable Retention Test
5 9.3 Cable anchorage Test for non-armorud Cable
6 9.4 Cable anchorage Test for armorud Cable
7 9.5 Resistance to Impact
8 10 Electrical properties
9 10.2 Ground Bond
10 10.3.2 Electrical current Test
11 11 Electromagnetic compatibility
12 12 12 External influences (IP) codes
13 12.2 Resistance to corrosion
14 13. Fire Hazard

If you are Interested Kindly Fill out the form below to receive a quote on the Cable Gland Testing to get started:

Contact Now! Puneet Sharma M: 08196980555 E: ITCIndiaOne@Gmail.Com

Provide us more details about your requirement, Please fill out the form below:
To Get Best Quote kindly describe your requirement for ‘ Cable gland Testing’

Cable Gland Testing in India

Posted on Updated on

ITC India Providing Cable Gland Testing Service in India. ITC can do Electrical Safety testing against Cable Gland Testing for following types of products/standards:
BS 6121: Specification for mechanical cable glands for elastomer and plastics insulated cables, IEC 62444: Cable glands for electrical, BS EN 50262: Cable glands for electrical installations Test carries out under this standard. installations

Cable retention test Cable anchorage test Cable anchorage twist test Impact test
Torque test Ingress protection (IP) test Electrical continuity test Insulation resistance test and more…

If you have any query regarding Cable Gland Testing and Certification. Kindly send us your testing requirements with the product technical details to submit you our testing charges.
We are waiting for your earliest reply. You can call or write us for any clarification
Puneet Sharma | +91.8196980555 | itcindiaone@gmail.com | ITC India Pvt. Ltd

Submit Your Testing Requirements,Please fill out the Enquiry below:

Cable Gland Testing

Posted on Updated on

Cable Gland Testing from NABL Accredited Laboratory, Cable Gland Testing from NABL Accredited Lab in India, Get Cable Gland Testing Service from NABL Accredited Laboratory in Mumbai, Chennai, Ahmedabad, Pune, Delhi, Ludhiana

Cable Gland Testing Expert ITC India NABL Accredited Laboratory Provide Cable gland testing As per Bs 6121 & Bs EN 50262
BS 6121:
Specification for mechanical cable glands for elastomer and plastics insulated cables
EN 62444:
Cable glands for electrical installations Test carries out under this standard.

If you are interested for Cable Gland Testing and Certification, you can send us you product technical specification with Images, so that we can provide testing facilities and price.
Puneet Sharma | 08196980555 | E-mail: Itcindiaone@gmail.com

Submit Your Testing Requirements,Please fill out the Enquiry below:

Cable Gland Testing as per IEC 62444

Posted on Updated on

ITC India Electrical Safety testing Laboratory Provide Testing service on Cable glands (CW), Cable glands (BW), Cable glands (E1W), Cable glands (A2) AS per IEC 62444 standard.

 

If you have any query regarding earth leakage current testing and Certification. Kindly send us your testing requirements with the product technical details to submit you our testing charges.

We are waiting for your earliest reply.

You can call or write us for any clarification.

Thanks & Regards,
Puneet Sharma
M: +91.8196980555
E-mail:-(itcindiaone@gmail.com)
ITC India Pvt. Ltd

Submit Your Testing Requirements,Please fill out the Enquiry below: